Electricians

Electrical Panel Clearance Requirements: The Working Space Rules in NEC 110.26

NEC 110.26 working space for a home electrical panel: 30 in wide, 36 in deep and 6 ft 6 in high, where panels cannot go and how to show it on a plan.

3 min read · 21 November 2026 · RoomPlot Team

Someone will need to stand in front of that panel one day, possibly in the dark, possibly in a hurry. The National Electrical Code keeps a box of clear space in front of it so they can work safely. It is one of the most common things inspectors fail, and one of the easiest to get right on a drawing.

NEC 110.26Working space in front of a panel PLAN VIEW 30 in wide 36 in deep Keep clear ELEVATION 6 ft 6 in Clear height or the equipment height, if taller Depth comes from Table 110.26(A)(1): 36 in is the usual figure for a 120/240 V home panel.
The working space in plan and elevation. Nothing is stored or built inside the shaded box.

Key takeaways

  • Width: at least 30 in, or the width of the equipment if that is greater.
  • Depth: 36 in in front of a typical 120/240 V home panel.
  • Height: clear to 6 ft 6 in, or the height of the equipment if taller.
  • Panels cannot go in bathrooms or clothes closets.

The three dimensions

Width

The working space is at least 30 in wide or the width of the equipment, whichever is greater. The panel does not have to be centred in it, so a panel can sit near a corner as long as the 30 in is there. The door or hinged cover must be able to open at least 90 degrees.

Depth

Depth is measured out from the front of the panel. It comes from Table 110.26(A)(1) and depends on the voltage and on what is opposite. For a 120/240 V residential panel the figure is 36 in.

Height

The space is clear from the floor to 6 ft 6 in, or to the top of the equipment if that is higher.

Dedicated space above and below

As well as the working space in front, the zone directly above and below an indoor panel, the width and depth of the equipment, is reserved for electrical equipment up to 6 ft above it or to the structural ceiling. Pipes, ducts and other foreign systems stay out of it.

Where a panel cannot go

  • Not in a bathroom.
  • Not in a clothes closet or near easily ignitable material.
  • Not where the highest breaker handle would be more than 6 ft 7 in above the floor.
  • Not over the steps of a stairway.

Check the rules. States and cities adopt different editions of the NEC, often with local amendments. This guide is a plain-English summary based on recent editions. Always check the edition your jurisdiction enforces and ask your inspector when in doubt.

Everyday problems

Most violations happen after the inspection. A water heater, a freezer or a set of shelves moves into the space. In garages, the car bumper ends up inside the 36 in. When you plan the room, treat the working space like a piece of furniture that is always there.

Show it on the plan

Place the panel symbol on the wall, then draw a 30 by 36 in rectangle in front of it and label it "working space, keep clear". In RoomPlot you can draw it as a zone at exact dimensions, so the homeowner, the cabinet installer and the inspector all see the same boundary.

Frequently asked questions

How much clearance does an electrical panel need?

For a typical home panel: a space at least 30 in wide, 36 in deep and 6 ft 6 in high in front of it.

Can a panel be in a closet?

Not in a clothes closet. Other closets and utility rooms are acceptable if the working space is kept clear.

Can I put a panel behind a door?

A door that swings in front of the panel is not prohibited in itself, but the working space must be clear when the panel is being worked on, and it cannot be used for storage.

Free lesson. Want the full picture? US rules for electrical plans is part of our free electrical floor plans course, with interactive exercises.

Sources

Plan it on your phone. Draw the panel and its working space to scale so nothing gets built in front of it. Download RoomPlot on the App Store and draw your first electrical plan in minutes, or see what it does on our electricians page.

Related guides

Electricians AFCI Requirements Explained: Which Rooms Need Arc-Fault Protection AFCI protection explained for US homes: what an arc fault is, the NEC 210.12 room list, what happens when you extend a circuit and how to plan it. 3 min read Electricians Consumer Unit Replacement in the UK: What Is Involved and What a Good Quote Includes Replacing a fuse box in the UK: what a modern consumer unit includes, the testing and certificates involved, Part P notification and how a circuit plan helps. 4 min read Electricians Cooker Circuit Guide: Cable Size, Diversity and the Cooker Switch UK cooker circuits explained: how diversity turns a 12 kW cooker into a 32 A circuit, typical cable sizes, where the cooker switch goes and how to draw it. 3 min read
Browse all guides