Electricians

Consumer Unit Replacement in the UK: What Is Involved and What a Good Quote Includes

Replacing a fuse box in the UK: what a modern consumer unit includes, the testing and certificates involved, Part P notification and how a circuit plan helps.

4 min read · 21 November 2026 · RoomPlot Team

Swapping an old fuse box for a modern consumer unit is one of the most valuable safety upgrades in a home. It is also more than a swap: every circuit is tested, faults are found and the job is certified. This guide explains what is involved, in plain English, for homeowners comparing quotes and for electricians explaining the work.

CONSUMER UNIT UPGRADEOld fuse board vs a modern consumer unit OLD BOARD Rewirable fuses or old breakers No RCD protection, or one RCD for everything No surge protection Plastic or wooden enclosure Faded or missing circuit labels MODERN CONSUMER UNIT One RCBO per circuit, so a fault trips only that circuit 30 mA RCD protection where it is required Surge protection device at the origin Non-combustible enclosure A clear circuit schedule that matches the plan
An old fuse board next to a modern consumer unit. The big changes are protection per circuit, surge protection and a clear schedule.

Key takeaways

  • A consumer unit replacement in England and Wales is notifiable work under Part P of the Building Regulations.
  • A modern unit usually has an RCBO per circuit, a surge protection device and a non-combustible enclosure.
  • Every circuit is inspected and tested, and you receive an Electrical Installation Certificate.
  • A circuit plan and schedule make the job faster and the finished board easier to live with.

Why replace a fuse box?

Older boards with rewirable fuses, or with no residual current device (RCD), do not give the shock and fire protection expected today. A modern consumer unit disconnects a faulty circuit in a fraction of a second, and with one RCBO per circuit a fault in the kitchen does not put the whole house in the dark.

What a modern consumer unit includes

  • Main switch to isolate the whole installation.
  • RCBOs, one per circuit, combining overcurrent and 30 mA RCD protection. A split-load board with two RCDs is the cheaper alternative.
  • Surge protection device (SPD) to protect electronics from voltage spikes.
  • A non-combustible enclosure, in practice steel, as BS 7671 requires for consumer units in homes.
  • Arc fault detection (AFDD) where required or chosen. BS 7671 requires it for socket circuits in some higher-risk residential buildings and recommends it elsewhere.

What happens on the day

  1. Checks before the swap. A good electrician inspects and tests first, so existing faults are found before the new, more sensitive protection finds them for you.
  2. Isolation and replacement. The power is off for most of the day while the old board comes out and the new one is wired.
  3. Testing. Each circuit is tested: continuity, insulation resistance, polarity, earth fault loop impedance and RCD operation.
  4. Labelling. Every way is labelled, and the circuit schedule is completed.
  5. Certification. You receive an Electrical Installation Certificate, and the work is notified to building control, normally through the electrician's competent person scheme.

Check the rules. Notification rules differ between England, Wales, Scotland and Northern Ireland. Check the current guidance for your nation before you start.

What a good quote includes

  • The make and type of board, and whether it uses RCBOs or a split-load arrangement.
  • Surge protection, and AFDDs if they are being fitted.
  • Testing of every circuit and what happens if a fault is found.
  • Any upgrade to main earthing and bonding.
  • The certificate and building control notification.

Where a plan helps

Many old boards have labels like "sockets" and "lights" and nothing else. Walking the house with a floor plan and marking which circuit feeds which room turns guesswork into a record. In RoomPlot you can place the consumer unit, colour each circuit and export the plan with its legend, so the schedule on the board finally matches the house.

Frequently asked questions

How long does a consumer unit replacement take?

For a typical home, most of a working day. It takes longer if testing finds faults that have to be put right before the new board can be energised.

Do I need to tell building control?

In England and Wales, replacing a consumer unit is notifiable. A registered electrician notifies it for you through their competent person scheme and you receive a compliance certificate.

Is a plastic consumer unit illegal?

Existing plastic units do not have to be removed just because they are plastic. New consumer units in homes must have a non-combustible enclosure, or be housed in one.

Free lesson. Want the full picture? Circuits explained is part of our free electrical floor plans course, with interactive exercises.

Sources

Plan it on your phone. Map every circuit to its rooms before the board is changed, and hand over a plan that matches the new schedule. Download RoomPlot on the App Store and draw your first electrical plan in minutes, or see what it does on our electricians page.

Related guides

Electricians AFCI Requirements Explained: Which Rooms Need Arc-Fault Protection AFCI protection explained for US homes: what an arc fault is, the NEC 210.12 room list, what happens when you extend a circuit and how to plan it. 3 min read Electricians Cooker Circuit Guide: Cable Size, Diversity and the Cooker Switch UK cooker circuits explained: how diversity turns a 12 kW cooker into a 32 A circuit, typical cable sizes, where the cooker switch goes and how to draw it. 3 min read Electricians Downlight Spacing Guide: How Many Downlights Does a Room Need? Work out how many downlights a room needs and how far apart to space them: the lumen method, a simple spacing rule, a worked example and common mistakes. 4 min read
Browse all guides