A Level 2 charger turns an overnight trickle into a full battery by morning. It is also one of the largest loads you can add to a house, and it runs for hours. Getting the circuit right starts with one rule and a sketch of the garage.
Key takeaways
- Level 1 charging uses a 120 V receptacle. Level 2 uses a 240 V circuit and charges several times faster.
- EV charging is a continuous load, so the circuit is rated at 125% of the charger's current.
- A 40 A charger needs a 50 A circuit. A 48 A charger needs a 60 A circuit and is hardwired.
- Check the panel has capacity with a load calculation, and get a permit.
Level 1 and Level 2
Level 1 is the cord that comes with the car, plugged into a 120 V receptacle. It adds a few miles of range per hour. Level 2 uses 240 V and adds roughly 15 to 40 miles of range per hour, depending on the car and the power of the charger.
The 125% rule
Charging runs for more than three hours, so the NEC treats it as a continuous load. The branch circuit and its breaker must be rated for at least 125% of the charger's maximum current.
| Charger output | Minimum circuit | Typical connection |
|---|---|---|
| 16 A | 20 A | Hardwired or plug-in |
| 32 A | 40 A | Hardwired or plug-in |
| 40 A | 50 A | Hardwired, or a 14-50 receptacle |
| 48 A | 60 A | Hardwired |
Wire size
The conductors are sized for the circuit rating. A 50 A circuit is typically 6 AWG copper. A 60 A circuit needs conductors good for 60 A at the terminal temperature rating, which rules out 6 AWG nonmetallic sheathed cable and usually means 6 AWG copper in conduit or 4 AWG cable. The installation manual states what the charger accepts.
Plug-in or hardwired?
A plug-in charger on a 240 V receptacle is easy to replace, but the receptacle needs GFCI protection and a heavy-duty receptacle rated for the duty. Hardwiring avoids the receptacle altogether, is required for chargers above 40 A and is often the more reliable choice.
Does the panel have room?
A 100 A service with electric heat or an electric range may not have capacity for a 60 A charger. A load calculation answers the question. If capacity is tight, the options are a smaller charger setting, a load management device that pauses charging when the house is busy, or a service upgrade.
Check the rules. States and cities adopt different editions of the NEC, often with local amendments. This guide is a plain-English summary based on recent editions. Always check the edition your jurisdiction enforces and ask your inspector when in doubt.
Sketch the garage
- Draw the garage with the vehicles parked and note where each car's charge port is.
- Place the charger where the cable reaches the port without crossing a walkway.
- Mark the panel and draw the circuit route between them.
- Read the route length for the wire order and the voltage drop check.
RoomPlot includes an EV charger symbol and totals the cable route as you draw. Exported as a PDF, the sketch is what many permit offices ask to see.
Frequently asked questions
What size breaker for a 48 amp EV charger?
60 A. The circuit must be rated at 125% of the charger's 48 A output.
Do I need a permit to install an EV charger?
In most jurisdictions, yes. A new 240 V circuit is permitted electrical work and is inspected.
Can I use a dryer outlet for EV charging?
Only with equipment designed for it and a circuit rated for the load. Sharing devices exist, but the charger must be set to a current the circuit can carry continuously.
Free lesson. Want the full picture? US rules for electrical plans is part of our free electrical floor plans course, with interactive exercises.
Sources
- NFPA 70, National Electrical Code: free online access and development
- US Department of Energy, Alternative Fuels Data Center: charging at home
- ENERGY STAR: Electric vehicle chargers
- NFPA: NEC adoption maps by state
Plan it on your phone. Sketch the garage, place the charger and get the cable run length before you call for quotes. Download RoomPlot on the App Store and draw your first electrical plan in minutes, or see what it does on our electricians page.