Electricians

How Many Outlets on a 15 Amp or 20 Amp Circuit? The Rule of Thumb Explained

How many outlets can go on a 15 A or 20 A circuit in a US home: what the NEC says, where the 8 to 10 and 10 to 13 rules of thumb come from and how to plan.

4 min read · 21 November 2026 · RoomPlot Team

Ask ten electricians how many receptacles can go on one circuit and you will hear "eight", "ten" and "it depends". All three are fair. For homes the National Electrical Code does not set a number at all. The familiar figures are rules of thumb, and it is worth knowing where they come from.

RULE OF THUMBOutlets on a 15 A and a 20 A circuit CIRCUIT COPPER WIRE 80% LOAD COMMON PRACTICE 15 A, 120 V 14 AWG 12 A, about 1,440 W 8 to 10 general receptacles 20 A, 120 V 12 AWG 16 A, about 1,920 W 10 to 13 general receptacles The NEC does not set a number for dwelling receptacles. The counts come from the 180 VA per outlet figure used for other occupancies.
The common rule of thumb. The NEC itself does not limit the number of general receptacles on a dwelling circuit.

Key takeaways

  • The NEC does not limit the number of general-purpose receptacles on a circuit in a dwelling.
  • The common guide is 8 to 10 on a 15 A circuit and 10 to 13 on a 20 A circuit.
  • Those numbers come from allowing 180 VA per receptacle, a figure the code uses for other building types.
  • What matters is the load: what will actually be plugged in, and for how long.

What the code says

For dwellings, general lighting and general-use receptacles are covered together by a load calculated from the floor area. There is no per-receptacle count. For other occupancies, the code assigns 180 volt-amperes to each receptacle, and that figure is the source of the rule of thumb.

The arithmetic

  • A 15 A, 120 V circuit can supply 1,800 VA. Divided by 180 VA, that is 10 receptacles.
  • A 20 A, 120 V circuit can supply 2,400 VA. Divided by 180 VA, that is 13 receptacles.

Many electricians stop at 8 on a 15 A circuit and 10 on a 20 A circuit to leave a margin.

The 80 percent idea

A load that runs for three hours or more is a continuous load, and a circuit should not carry more than 80% of its rating continuously: 12 A on a 15 A circuit, 16 A on a 20 A circuit. A single 1,500 W space heater draws 12.5 A, so it nearly fills a 15 A circuit on its own, however few receptacles are on it.

Circuits with their own rules

The rule of thumb is for general receptacles in bedrooms and living areas. Other circuits are fixed by the code:

  • Kitchen countertops: at least two 20 A small-appliance circuits.
  • Bathrooms: a 20 A circuit for the receptacles.
  • Laundry: a 20 A circuit for the laundry receptacles.
  • Garage: a 20 A circuit for the garage receptacles.
  • Fixed appliances: dedicated circuits sized to the appliance.

Check the rules. States and cities adopt different editions of the NEC, often with local amendments. This guide is a plain-English summary based on recent editions. Always check the edition your jurisdiction enforces and ask your inspector when in doubt.

Plan by use, not by count

Think about what each room will run. A home office with computers and a laser printer, or a media wall, deserves its own circuit. A guest bedroom does not. Splitting a large room across two circuits means one trip never leaves it completely dead.

On a floor plan this is easy to see. In RoomPlot, draw each circuit's route in its own colour and count the receptacle symbols along it. If one colour is doing all the work in a room full of equipment, split it.

Frequently asked questions

Can I mix lights and outlets on the same circuit?

In general living areas, yes. The kitchen small-appliance, bathroom and laundry receptacle circuits have restrictions on what else they can supply.

Can I put 15 A receptacles on a 20 A circuit?

Yes, where there are two or more receptacles on the circuit. A standard duplex receptacle counts as two.

How many outlets can a 20 amp circuit have in a kitchen?

There is no count, but the kitchen needs at least two 20 A small-appliance circuits, and the receptacle positions are set by the countertop spacing rule.

Free lesson. Want the full picture? Circuits explained is part of our free electrical floor plans course, with interactive exercises.

Sources

Plan it on your phone. Colour each circuit on the plan and see at a glance which ones are carrying too much. Download RoomPlot on the App Store and draw your first electrical plan in minutes, or see what it does on our electricians page.

Related guides

Electricians AFCI Requirements Explained: Which Rooms Need Arc-Fault Protection AFCI protection explained for US homes: what an arc fault is, the NEC 210.12 room list, what happens when you extend a circuit and how to plan it. 3 min read Electricians Consumer Unit Replacement in the UK: What Is Involved and What a Good Quote Includes Replacing a fuse box in the UK: what a modern consumer unit includes, the testing and certificates involved, Part P notification and how a circuit plan helps. 4 min read Electricians Cooker Circuit Guide: Cable Size, Diversity and the Cooker Switch UK cooker circuits explained: how diversity turns a 12 kW cooker into a 32 A circuit, typical cable sizes, where the cooker switch goes and how to draw it. 3 min read
Browse all guides