Electricians

RCD Types Explained: AC, A, F and B, and Which One a Circuit Needs

RCD types AC, A, F and B explained in plain English: what each detects, why Type AC is being phased out in UK homes and how to note the type on a plan.

3 min read · 21 November 2026 · RoomPlot Team

Not all RCDs are the same. The letters AC, A, F and B describe which kinds of fault current the device can detect, and choosing the wrong one can leave a circuit with protection that does not operate when it should. Here is the difference, without the jargon.

RCD TYPESWhich RCD type detects what TYPE DETECTS TYPICAL USE AC Alternating residual current only Older installations. Now limited to loads with no DC components A AC plus pulsating DC The usual choice for general domestic circuits F Type A plus mixed frequencies Single-phase inverter loads: some washing machines, air conditioning, heat pumps B Type F plus smooth DC Three-phase drives, some EV charging and solar or battery inverters Always follow the equipment manufacturer's instructions when choosing the RCD type.
The four RCD types. Each one detects everything the type above it does, plus more.

Key takeaways

  • An RCD trips when current leaks to earth. The type letter says which shapes of leakage current it can see.
  • Type AC only detects plain alternating current and is now limited to loads with no DC components.
  • Type A is the usual choice for general circuits in UK homes.
  • Inverter-driven and DC-producing equipment may need Type F or Type B: check the manufacturer's instructions.

What an RCD does

A residual current device compares the current going out on the line conductor with the current coming back on the neutral. If some is missing, it is leaking to earth, possibly through a person. A 30 mA RCD disconnects quickly enough to prevent most fatal shocks. An RCBO is the same protection combined with a circuit breaker in one device.

The four types

Type AC

Detects alternating residual current only. Modern appliances full of electronics can put DC components into a fault current, and that can stop a Type AC device from tripping. Since Amendment 2 of BS 7671, Type AC is only for fixed equipment where the load is known to contain no DC components.

Type A

Detects alternating and pulsating DC residual currents. This covers most household equipment and is the general-purpose choice for domestic circuits.

Type F

Everything Type A does, plus mixed-frequency residual currents from single-phase inverter drives, found in some washing machines, air conditioning units and heat pumps.

Type B

Everything Type F does, plus smooth DC. Used with three-phase drives and some electric vehicle charging, solar and battery equipment.

Check the rules. Equipment manufacturers often state the RCD type required. Where they do, that instruction decides the choice. Check the current edition of BS 7671 for the exact requirements.

EV chargers and solar

Electric vehicle charging is the most common place a homeowner meets this question. A charging point needs protection against DC fault currents: either a Type B RCD, or a Type A (or F) RCD together with a device that detects 6 mA of DC, which many chargers have built in. Solar and battery inverters come with their own requirements in the installation manual.

Show the type on the plan

When you plan a new circuit, note the protective device against it: for example "C6 EV charger, 32 A, Type A RCBO plus 6 mA DC detection". In RoomPlot each cable route has its own colour and label, and a text note beside the consumer unit keeps the device choices on the same sheet as the layout.

Frequently asked questions

How do I tell which type of RCD I have?

Look for the symbol on the front of the device. Type AC shows a single sine wave in a box. Type A shows the sine wave with a pulsed wave below it. Types F and B add further symbols and are usually marked with the letter.

Do I have to replace my Type AC RCDs?

There is no blanket requirement to replace existing devices. An inspection may recommend improvement where Type AC protects circuits with DC-producing loads. New work should use the appropriate type.

Is an RCBO better than an RCD?

An RCBO protects a single circuit, so a fault trips only that circuit. A shared RCD protects several circuits at once, so one fault switches all of them off.

Free lesson. Want the full picture? Circuits explained is part of our free electrical floor plans course, with interactive exercises.

Sources

Plan it on your phone. Label every circuit with its protective device and keep the design on one sheet. Download RoomPlot on the App Store and draw your first electrical plan in minutes, or see what it does on our electricians page.

Related guides

Electricians AFCI Requirements Explained: Which Rooms Need Arc-Fault Protection AFCI protection explained for US homes: what an arc fault is, the NEC 210.12 room list, what happens when you extend a circuit and how to plan it. 3 min read Electricians Consumer Unit Replacement in the UK: What Is Involved and What a Good Quote Includes Replacing a fuse box in the UK: what a modern consumer unit includes, the testing and certificates involved, Part P notification and how a circuit plan helps. 4 min read Electricians Cooker Circuit Guide: Cable Size, Diversity and the Cooker Switch UK cooker circuits explained: how diversity turns a 12 kW cooker into a 32 A circuit, typical cable sizes, where the cooker switch goes and how to draw it. 3 min read
Browse all guides