Electricians

Ring Final Circuit on a Floor Plan: How to Draw and Check It

Draw a ring final circuit on a floor plan: 2.5 mm² on 32 A, the 100 m² guide, spurs, radial alternatives, RCD and AFDD protection, shown clearly.

4 min read · 20 November 2026 · RoomPlot Team

The ring final circuit is the backbone of UK socket wiring, and it is also the circuit most often drawn badly. A ring has to leave the consumer unit, visit every socket and come back to the same protective device. Drawing it that way on the plan makes it easy to check, quote and test. This guide covers the usual design rules and how to show a ring clearly.

The usual ring final arrangement

  • Cable and protection: 2.5 mm² twin and earth on a 32 A device is the classic arrangement.
  • Floor area: IET guidance limits one ring to a floor area of up to 100 m², with no fixed limit on the number of sockets. Larger homes simply have more rings.
  • Kitchens: heavy appliance loads mean a kitchen usually gets its own ring or radial.
  • Radial alternative: a 20 A radial in 2.5 mm² is commonly used for areas up to about 50 m², such as a garage or a home office.
USB C2 C3 Both ends of each ring land on the same wayKitchen Bathroom Bedroom Garage Ring final circuits Each loop leaves and returns to the CU CIRCUITS (CABLE ROUTES) C2 Kitchen ring 2.5 mm² · 32 A RCBO C3 Sockets ring 2.5 mm² · 32 A RCBO SYMBOLS Double socket Fused spur Consumer Unit
Two ring final circuits on one plan. Each loop leaves the consumer unit, passes every double socket and returns to the same way.

Key takeaways

  • A ring final leaves the consumer unit, visits every socket and returns to the same protective device.
  • The classic arrangement is 2.5 mm² cable on a 32 A device, serving up to 100 m² of floor area.
  • An unfused spur feeds one single or one double socket and comes off the ring itself.
  • Drawing the loop closed on the plan makes the circuit easy to check and test.

Spurs: what the plan should make obvious

A spur is a branch off the ring. Unfused spurs are normally limited to one single or one double socket per spur, and the number of unfused spurs should not exceed the number of sockets on the ring itself. Fixed appliances such as a boiler, a cooker hood or an integrated fridge are usually fed through a fused spur instead. In RoomPlot, add a junction on the ring route and branch off it, so the spur is visibly a branch and not part of the loop.

Protection: RCDs and AFDDs

Socket-outlets rated up to 32 A generally need 30 mA RCD protection, and cables buried in walls at less than 50 mm usually need it too, which is why most new consumer units protect every circuit with an RCBO. Arc fault detection devices are now required for socket circuits in houses in multiple occupation and higher-risk residential buildings, and recommended elsewhere.

Check the standard. Ring sizes, floor areas and protection rules come from BS 7671 and the IET On-Site Guide. Always confirm them against the current edition and the actual cable length, installation method and voltage drop for the job.

Common mistakes

  • A ring that never closes. If the route on the plan does not return to the same way, it is a radial, and should be designed as one.
  • Spurs off spurs. Each unfused spur should come off the ring itself, not off another spur.
  • One ring for a large extension. Check the floor area served against the guidance and add a circuit where needed.
  • Kitchen sockets on the general ring. Heavy appliance loads are better on their own circuit.

Why drawing the loop helps testing

Ring continuity testing checks the line, neutral and protective conductors end to end. When the plan shows both ends of the ring landing on the same way, with every socket on the loop and every spur as a branch, the person testing knows exactly what they should find. Give each ring its own circuit colour and name, and the PDF report carries the same names into the schedule. More trade guides are on our electricians page.

Frequently asked questions

What is the difference between a ring and a radial circuit?

A ring returns to the consumer unit, so current has two paths to each socket. A radial runs out from the consumer unit and ends at the last point.

Can I spur off a spur?

No. Each unfused spur should come directly off the ring and feed one single or one double socket.

Do ring circuits need RCD protection?

Socket-outlets rated up to 32 A generally need 30 mA RCD protection, which is why modern consumer units usually have an RCBO on each socket circuit.

Free lesson. Want the full picture? Sockets and spurs is part of our free electrical floor plans course, with interactive exercises.

Related guides

Electricians AFCI Requirements Explained: Which Rooms Need Arc-Fault Protection AFCI protection explained for US homes: what an arc fault is, the NEC 210.12 room list, what happens when you extend a circuit and how to plan it. 3 min read Electricians Consumer Unit Replacement in the UK: What Is Involved and What a Good Quote Includes Replacing a fuse box in the UK: what a modern consumer unit includes, the testing and certificates involved, Part P notification and how a circuit plan helps. 4 min read Electricians Cooker Circuit Guide: Cable Size, Diversity and the Cooker Switch UK cooker circuits explained: how diversity turns a 12 kW cooker into a 32 A circuit, typical cable sizes, where the cooker switch goes and how to draw it. 3 min read
Browse all guides