Symbols are the vocabulary of an electrical drawing. Use the right ones consistently and anyone on the job can read the plan without asking; mix families and a dimmer starts to look like a socket. This guide walks through the symbols that appear on almost every domestic electrical floor plan, with the UK and US name for each one, as RoomPlot draws them.
Why one symbol family matters
UK drawings traditionally follow IEC 60617 style graphical symbols, published in the UK as BS EN 60617, while US drawings use their own conventions for receptacles, switches and panels. Neither is hard to read on its own. The trouble starts when a plan mixes them: two different-looking two-way switches on the same sheet suggest two different devices. Pick a family for the job and stay with it.
Key takeaways
- Pick one symbol family for the job and use it on every sheet.
- UK and US plans often use the same symbol under a different name: two-way and three-way switch, double socket and duplex receptacle.
- Sockets, spurs and switches belong on a wall, with their stems touching it.
- A legend generated from the symbols you placed keeps the key and the quantities in step.
Lighting
RoomPlot's lighting symbols share a yellow housing so lights stand out from everything else on the plan: pendant fixture, surface ceiling light, recessed ceiling light, LED panel, luminaire, floor light, wall light and outdoor light. Downlights in a kitchen ceiling and a single pendant in a bedroom read differently at a glance, which helps when you count fittings for a quote.
Switches
- One-way switch - a circle with a single stem and flag, the everyday light switch.
- Two-way switch - stems on both sides of the circle, used in pairs to control one light from two places, such as the top and bottom of a staircase.
- Intermediate switch - the cross switch, fitted between two two-way switches to add a third or fourth control point. In US terms these are three-way and four-way switches.
- Dimmer, double pole, pull-cord and multi-gang switches complete the family.
Sockets and spurs
In the Sockets & Spurs group, sockets are drawn as a circle with stems that meet the wall: one stem for a single socket, two for a double, with variants for USB, waterproof and GFCI outlets. A fused spur uses the same visual language with an open cup, so it sits naturally alongside the sockets on a kitchen wall. With the US filter on, the same family is labelled as receptacles, which keeps a mixed UK and US portfolio consistent.
Distribution and safety
The consumer unit (UK) and panelboard (US) mark where every circuit starts. Add the cooker control unit, extractor fans, immersion heater, smoke, heat and carbon monoxide alarms, EV charger and data outlets from their own groups. For commercial fire work, the separate Fire Safety library adds detectors that draw their coverage on the plan, covered in our guide to smoke detector coverage.
Tip. Favourite the symbols you use on every job so they are always one tap away, and a full house layout takes minutes rather than an afternoon of scrolling.
Common mistakes
- Two styles for one device. A two-way switch drawn two different ways on one sheet reads as two different products.
- US receptacles on a UK plan, or the other way round. Set the UK or US filter once at the start of the job.
- Symbols floating in the room. Sockets, spurs and switches belong on a wall, with the stems touching it.
- Text you cannot read at print size. Check the exported PDF at 100 percent before it goes to the client.
Let the legend write itself
Every symbol you place is tallied in the legend of the exported report, so the drawing, the key and the quantities always agree. That is the simplest way to make sure a client, a building control officer and the second fix team are reading the same thing. Browse the full board on our electricians page.
Frequently asked questions
What is the symbol for a light switch on a floor plan?
A small circle with a stem and a flag. A two-way switch has stems on both sides, and an intermediate switch is drawn as a cross.
Are UK and US electrical symbols different?
The naming differs more than the devices. A UK two-way switch is a US three-way switch, and a UK double socket is a US duplex receptacle. RoomPlot uses one symbol and shows the name for the region you choose.
Does an electrical plan need a legend?
Yes. The legend lists every symbol on the sheet so that the client, the inspector and the installer all read it the same way.
Free lesson. Want the full picture? Electrical symbols is part of our free electrical floor plans course, with interactive exercises.