Module 2 · Designing a layout · Lesson 5 of 18

Lighting and switching: one-way, two-way and intermediate

Free lesson: plan lighting layers and switching, including two-way and intermediate switching, and show it clearly with switch connections.

8 min · 0 XP · 0 of 18 lessons done

Lesson 5 of 18 All lessons
  1. 1What an electrical floor plan is, and who uses it
  2. 2Electrical symbols: lights, switches, sockets and distribution
  3. 3Circuits explained: lighting, rings, radials and dedicated supplies
  4. 4Drawing the base plan: measuring, doors and fixed fittings
  5. 5Lighting and switching: one-way, two-way and intermediate
  6. 6Sockets and spurs: how many, where, and on which circuit
  7. 7Kitchens and bathrooms: special rules for special rooms
  8. 8Cable routes, lengths and circuit schedules
  9. 9Dedicated circuits: showers, cookers, EV chargers and outbuildings
  10. 10UK rules: BS 7671, Part P and what applies where
  11. 11UK protection: consumer units, RCD types and surge protection
  12. 12UK earthing systems, mounting heights and certificates
  13. 13US rules: the NEC, receptacle spacing, GFCI and AFCI
  14. 14US kitchens and bathrooms: receptacle rules on the plan
  15. 15US panels, GFCI, AFCI and wire sizes
  16. 16Worked example: from survey to a finished plan
  17. 17Checking your plan and handing it over
  18. 18Final test: check what you have learned

In this lesson

  • Show switching with connections from each switch to its lights.
  • Two-way switching uses two switches and strappers; intermediate adds a third point.
  • Strappers carry line voltage and are sleeved brown in the UK.

Lighting is where an electrical plan shows its value: which lights go where and, just as important, which switch turns each one on.

C1 Kitchen Bathroom Bedroom Garage Lighting circuit Cable route plus switch connections CIRCUITS (CABLE ROUTES) C1 Lighting 1.5 mm² · 6 A RCBO Connection (switch to light) SYMBOLS Pendant fixture light Surface ceiling light Recessed ceiling light One-way switch Two-way switch Dimmer switch Consumer Unit
A lighting circuit (yellow) with red connections showing which switch controls which light.

Plan in layers

Most rooms benefit from general light, feature light and task or accent light, each on its own switch. Put switches by the door on the latch side, and add a dimmer where you will want lower light in the evening.

Show the switching

Draw a connection from each switch to the lights it controls. A reader then sees the switching arrangement instantly, without a separate diagram.

Two-way and intermediate

A light controlled from two places uses two two-way switches joined by two strappers. Add an intermediate switch between them for a third point, common on landings. In the UK, strappers usually run in three-core and earth, and the grey and black cores are sleeved brown because they carry line voltage.

Switch A (two-way)Bottom of the stairs COM L1 L2 IntermediateLanding L1 L2 L1 L2 Switch B (two-way)Top of the stairs COM L1 L2 Line in from the lighting circuit Switched line NeutralLanding light Brown sleeve: strappers carry line voltageGrey strapperBlack strapper
Two two-way switches and an intermediate switch joined by brown-sleeved strappers.

Free calculators for this lesson: downlight spacing calculator, lumens calculator.

Try it

Pick a room with two doors. Draw two-way switching for its main light, with a connection from each switch to the light.

Check your understanding

Official documents and further reading

Progress is saved in this browser.

Go deeper: related guides

Electricians Lighting Circuit Floor Plan: Switches, Two-Way and Intermediate Plan a lighting circuit on a floor plan: radial lighting cable routes, switch connections, two-way and intermediate switching and strapper colours. 4 min read Electricians Living Room Lighting Plan: A Step-by-Step Guide Plan living room lighting in layers: downlights on a dimmer, a pendant and wall lights, each with its own switch, drawn on a floor plan step by step. 3 min read Electricians Bedroom Electrical Plan: Sockets, Lighting and Switching Plan bedroom electrics: sockets and reading lights either side of the bed, two-way switching from the door and the bed, and data for a TV or desk. 3 min read